Posts made by jugg

我也试了微雪的这个5寸屏
不支持双指 打开一张本地的图片 不能用双指进行缩放 只能用鼠标滚轮缩放
但是这个屏接树莓派4b是能用双指缩放的
这个需要改哪里吗？

@george
但是gst还没有适配gst、ffmpeg的mpp硬件支持

@jugg 我试了debian不行
UOS的估计也不行

@george debian系统呢

不是新适配了UOS的系统吗
那UOS的能不能复制显示？

有没有计划解决这个多屏复制显示的问题

@大法师
U盘16G 备份的系统3个G不到
这个就是备份盘 备份出来的backup文件夹的内容

串口输出

COOLPI LOADER BY YANYI(Jan 04 2023)

DRAM:  8 GiB
Using default environment

0 2 1 3 6 8 7 9 trsv ln0 mon rx cdr lock timeout
dp@fde50000 disconnected
Monitor has basic audio support
hdmi info isn't saved in main block
mode:1920x1080 bus_format:0x100a
hdmi@fde80000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: hdmi0_phy_pll may not define
rockchip_vop2_init: hdmi1_phy_pll may not define
assigned-clock-parents's node not define
VP0 set crtc_clock to 148500KHz
VOP VP0 enable Esmart0[356x124->356x124@782x478] fmt[1] addr[0xedf21000]
CEA mode used vic=16
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
Autoboot in 1 seconds
trsv ln0 mon rx cdr lock timeout
dp@fde50000 disconnected
VOP VP0 enable Esmart0[356x124->356x124@782x478] fmt[1] addr[0xedf21000]
starting USB...
Bus usb@fc880000: USB EHCI 1.00
scanning bus usb@fc880000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Generic  Rev: 8.07 Prod: Flash Disk      
            Type: Removable Hard Disk
            Capacity: 30000.0 MB = 29.2 GB (61440000 x 512)
... is now current device
Scanning usb 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
274 bytes read in 35 ms (6.8 KiB/s)
1:	Linux coolpi
Retrieving file: /initrd.img
reading /initrd.img
8913121 bytes read in 807 ms (10.5 MiB/s)
Retrieving file: /Image
reading /Image
37706240 bytes read in 3478 ms (10.3 MiB/s)
append: root=LABEL=writable rw rootfstype=ext4 console=tty0 quiet splash plymouth.ignore-serial-consoles vt.global_cursor_default=1 irqchip.gicv3_pseudo_nmi=0 net.ifnames=0 rtleth=ethaddr:d6:c9:c9:a0:cf:46
Retrieving file: /rk3588s-cp4.dtb
reading /rk3588s-cp4.dtb
141838 bytes read in 47 ms (2.9 MiB/s)
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Loading Ramdisk to eb154000, end eb9d40e1 ... OK
   Loading Device Tree to 00000000eb12e000, end 00000000eb153a0d ... OK
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000)

Starting kernel ...

I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot

显示器输出

我这备份出来的系统无法还原 我都试了很多次了

@jack_admin
有没有一个靠谱的方法备份、还原系统？

@jack_admin 没用 刷了 还是进不去

昨天我用我之前做的备份盘 备份系统 发现一备份就死机
然后重新刷了备份盘 备份成功
结果还原的系统进不去
然后又刷了还原盘
结果还原的还是进不去
(https://cool-pi.com/topic/360/系统备份异常/6)

@大法师

备份盘的backup里面的内容已经剪切出来了

rufus 做的系统盘和备份盘
这中间有什么问题?

这些系统盘和备份盘 都是我新做的
之前做的盘备份、还原都行
这次的不行 我就重新刷了一遍 结果还是一样

@大法师

把备份盘的放到这里 不就可以了？
备份的时候显示器有进度 还原过程显示器也有进度 中间都没有异常
但是还原的系统就是上面那样 开不了机

这就是还原出来的系统 两次都这样 根本启动不了

@大法师
根本就还原不了 各种问题

@jack_admin

这里最近的就是0306的
现在0613的备份 能不能用这个来还原

@jack_admin
是4B 用U盘备份
U盘的内容我没动过 备份几次之后就这样了
把U盘重新刷了 又能备份了

这个备份U盘之前备份过之前旧的系统 可以备份 可以还原 就这个不行

新刷的0613的系统

然后用U盘备份

开机后就出现内核崩溃

不接备份U盘 能正常进系统

Connecting to COM4...
Connected.

¿ÿ񁀿ÿÿDDR V1.09 a930779e06 typ 22/11/21-17:50:56
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0xff
CH0 RX Vref:30.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:21.8%,21.8%
CH2 RX Vref:28.7%, TX Vref:21.8%,21.8%
CH3 RX Vref:29.7%, TX Vref:22.8%,20.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-557-g9609b9c19:derrick.huang
NOTICE:  BL31: Built : 14:29:57, Mar  8 2023
INFO:    spec: 0x13
INFO:    ext 32k is not valid
INFO:    ddr: stride-en 4CH
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-652-g4542e1efd #derrick.huang (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #5 2022年 09月 20日 星期二 09:41:09 CST aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


COOLPI LOADER BY YANYI(Jun 06 2023)

DRAM:  8 GiB
Using default environment

switch to partitions #0, OK
mmc0(part 0) is current device
reading logo.bmp
FAT: Misaligned buffer address (00000000ebc9e610)
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo.bmp
0 2 1 3 6 8 7 9 Monitor has basic audio support
hdmi info isn't saved in main block
mode:1920x1080 bus_format:0x100a
hdmi@fde80000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
dclk:148500,if_pixclk_div;2,if_dclk_div:4
rockchip_vop2_init: hdmi1_phy_pll may not define
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
VP0 set crtc_clock to 1485KHz
VOP VP0 enable Esmart0[1920x1080->1920x1080@0x0] fmt[1] addr[0xee4ef000]
CEA mode used vic=16
mtmdsclock:148500000
bus_width:0x16a8c8,bit_rate:1485000
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
boot mode: None
Autoboot in 1 seconds
VOP VP0 enable Esmart0[1920x1080->1920x1080@0x0] fmt[1] addr[0xee4ef000]
starting USB...
Bus usb@fc000000: usb maximum-speed not found
trsv ln0 mon rx cdr lock timeout
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc000000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 2 USB Device(s) found
scanning bus usb@fcd00000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Generic  Rev: 8.07 Prod: Flash Disk      
            Type: Removable Hard Disk
            Capacity: 30000.0 MB = 29.2 GB (61440000 x 512)
... is now current device
Scanning usb 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
274 bytes read in 35 ms (6.8 KiB/s)
1:	Linux coolpi
Retrieving file: /initrd.img
reading /initrd.img
8202961 bytes read in 796 ms (9.8 MiB/s)
Retrieving file: /Image
reading /Image
37706240 bytes read in 3647 ms (9.9 MiB/s)
append: root=LABEL=writable rw rootfstype=ext4 console=tty0 quiet splash plymouth.ignore-serial-consoles vt.global_cursor_default=1 irqchip.gicv3_pseudo_nmi=0 net.ifnames=0 rtleth=ethaddr:96:39:8b:af:40:ae
Retrieving file: /rk3588s-cp4.dtb
reading /rk3588s-cp4.dtb
141838 bytes read in 46 ms (2.9 MiB/s)
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Loading Ramdisk to eb201000, end eb9d3ad1 ... OK
   Loading Device Tree to 00000000eb1db000, end 00000000eb200a0d ... OK
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo_kernel.bmp
FAT: Misaligned buffer address (00000000ebcb6950)
switch to partitions #0, OK
mmc0(part 0) is current device
reading logo_kernel.bmp
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Adding bank: 0x2f0000000 - 0x300000000 (size: 0x10000000)

Starting kernel ...

I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boo

就卡在这里不动了
显示器上面是内核崩溃一样的信息打印

@george
不过用vlc播放一个本地的mp4文件 是黑屏 播放不出来 用mpv可以播

@george
默认的MPV没有问题
只是不解 只是换了屏幕 就出现问题

这是一个基于mpv的视频播放器
My_MPV_Qt_demo
我在hdmi显示器下打开播放一个视频播放正常
换成dsi的显示屏（微雪5寸 分辨率800x480）视频的窗口会从qt框架中脱离出来 默认就全屏了
我试了0306系统 0613系统 X11 Wayland 都是同样的结果
这是代码 基本是官方的代码
My_MPV_Qt_demo-main.zip
这可能和什么有关
代码应该没问题

@george
debian没有像ubuntu那样的ext文件修改

@george
CM4
接微雪的5寸屏 800x480

@george
这个没有可以改支持dsi显示屏的
要怎么改才能支持排线的屏幕

@jugg said in 连接多个屏幕问题:

@george
刷了0613的系统
/boot/fireware里面是空的
没法改dsi
还要再更新内核？
8G多的镜像 没有更新loader和内核？

重启了 又有了 改成dsi的
接dsi的屏幕和hdmi的显示器
dsi有画面 显示器没有
而且系统也没识别到hdmi显示器

@george
刷了0613的系统
/boot/fireware里面是空的
没法改dsi
还要再更新内核？
8G多的镜像 没有更新loader和内核？

@jack_admin
我刷了最新的0613的系统 难道还要更新loader 才能按3下进入UMS？

@george
其它系统呢？
buildroot、armbian 都不行吗？
还是以后都不会有mirror

@george
就是coolpi这个用户改不掉
因为我要批量的刷机 要改用户
新刷的系统这个用户去不掉也改不了

但是之前的系统 新刷的是自己创建用户

@george
我刷了0613-22.04的系统 能切换X11和Wayland
但是能不能像之前的系统一样
新刷的系统第一次进去由系统引导来创建用户
现在的系统默认就有用户 改不掉